Inability to start the vehicle: A faulty starter will prevent the engine from cranking, leaving the vehicle inoperable— a major inconvenience for daily commuting or long-distance travel.
Damage to other engine components: A stuck or malfunctioning starter can cause excessive load on the engine’s flywheel, leading to wear or damage to the flywheel ring gear.
Increased battery consumption: A starter with poor performance (e.g., high resistance in the windings) will draw more current from the battery, accelerating battery aging and even causing battery depletion.
Compromised driving safety: Unexpected starter failure in emergency situations (e.g., on highways, remote areas) can pose safety risks, especially if the vehicle cannot be restarted promptly.
Voltage Rating: Chery iCAR new energy vehicles typically use a 48V or 72V electrical system (depending on the model). The starter’s voltage rating must match the vehicle’s system voltage— using a starter with the wrong voltage rating will cause it to fail to operate or burn out the windings.
Power Output: The starter’s power output (measured in kilowatts, kW) must be sufficient to crank the Chery iCAR’s engine. A starter with insufficient power will struggle to start the engine, especially in low-temperature conditions, leading to premature wear.
Installation Dimensions: The starter’s mounting holes, shaft length, and overall size must match the engine’s mounting bracket. A starter with incorrect dimensions will not fit properly, leading to vibration, noise, and potential damage during operation.
Electrical Interface: The starter’s connector must match the vehicle’s wiring harness. A mismatched interface will require modification of the wiring, which can cause short circuits or poor contact.
Copper Windings: The armature and field windings are made of high-purity copper, which has excellent conductivity and heat resistance. Copper windings ensure efficient current transmission and reduce energy loss, preventing overheating during operation. Avoid starters with aluminum windings, which have poor conductivity and are prone to burning out.
High-Strength Drive Gear and One-Way Clutch: The drive gear is made of high-carbon steel with heat treatment, ensuring wear resistance and impact resistance. The one-way clutch (which prevents the engine from driving the starter after startup) is made of high-quality alloy materials, ensuring reliable operation and long service life.
Heat-Resistant Housing: The starter’s housing is made of high-temperature-resistant aluminum alloy or engineering plastic, which can withstand the high temperatures in the engine compartment (up to 120°C or higher). The housing also has good heat dissipation performance, preventing the starter from overheating due to prolonged operation.
Reliable Solenoid: The solenoid uses high-quality coils and contacts, ensuring strong electromagnetic force and stable switching performance. A reliable solenoid ensures that the drive gear engages smoothly with the flywheel ring gear, avoiding grinding or slipping.
Quality Certifications: Look for starters that have passed international certifications such as ISO 9001 (quality management system) or CE (safety certification). These certifications indicate that the product meets global quality and safety standards.
Warranty Period: Reliable brands offer a clear warranty period (e.g., 1 year, 2 years) for their starters. This provides peace of mind for auto parts professionals and Chery iCAR owners, as faulty products can be replaced free of charge within the warranty period.
After-Sales Service: Good brands provide professional after-sales service, including technical support and troubleshooting assistance. This is especially valuable for auto parts distributors and repair shops that need to resolve issues quickly.
OEM (Original Equipment Manufacturer) Starters: These are starters produced by the same manufacturer that supplies Chery’s factories. They are identical to the original starters installed in the Chery iCAR at the factory, ensuring 100% compatibility and performance. OEM starters are the best choice for Chery iCAR owners who want to maintain the vehicle’s original performance and reliability. However, they are typically the most expensive option.
OES (Original Equipment Service) Starters: These are starters produced by third-party manufacturers authorized by Chery. They meet the same quality standards as OEM starters but are sold under the manufacturer’s brand name (not Chery’s). OES starters offer the same level of compatibility and performance as OEM starters but are often more affordable. They are a popular choice for auto repair shops and parts distributors.
Aftermarket Starters: These are starters produced by independent manufacturers that are not authorized by Chery. High-quality aftermarket starters are designed to match the original specifications and can offer good performance at a lower price than OEM or OES starters. However, there is a wide variation in quality among aftermarket starters— some are of excellent quality, while others are substandard. When choosing aftermarket starters, it is critical to select products from reputable brands with good reviews.
Replacement starter (matching the original specifications)
Socket wrench set (including deep sockets and extension bars)
Screwdriver set (flathead and Phillips head)
Pliers (locking pliers and needle-nose pliers)
Multimeter (for testing the electrical system)
Jack and jack stands (for lifting the vehicle if necessary)
Gloves and goggles (to protect hands and eyes from sharp edges and dirt)
Battery terminal puller (for disconnecting the battery)
Disconnect the battery: Before working on any electrical component, turn off the vehicle’s power and remove the negative terminal of the battery. This prevents short circuits and electric shock.
Allow the engine to cool: If the engine has been running, wait for it to cool down before accessing the engine compartment (to avoid burns from hot components).
Secure the vehicle: If you need to lift the vehicle to access the starter, use a jack and jack stands to secure it firmly. Never work under a vehicle supported only by a jack.
Label the wiring: Before disconnecting the starter’s wiring harness, label the wires to ensure correct reconnection. This avoids confusion during the installation of the new starter.
Locate the starter: The Chery iCAR starter is typically located at the bottom of the engine, near the flywheel. Refer to the vehicle’s service manual to find the exact location.
Disconnect the wiring harness: Use pliers or a screwdriver to disconnect the electrical connector from the starter’s solenoid. If the connector is tight, gently wiggle it while pulling to avoid damaging the wires.
Remove the mounting bolts: Use a socket wrench to remove the bolts that secure the starter to the engine’s mounting bracket. There are usually 2-3 mounting bolts— keep track of their positions to ensure correct reinstallation.
Remove the old starter: Once the mounting bolts are removed, carefully pull the old starter out of the engine compartment. Be careful not to damage the surrounding components (e.g., hoses, wires) during removal.
Inspect the mounting surface and flywheel: Before installing the new starter, inspect the engine’s mounting surface for dirt, debris, or damage. Also, check the flywheel ring gear for wear or teeth damage— if the ring gear is damaged, it should be replaced to avoid damaging the new starter’s drive gear.
Install the new starter: Position the new starter onto the mounting bracket, aligning the bolt holes. Insert the mounting bolts and tighten them securely (follow the torque specifications in the vehicle’s service manual).
Reconnect the wiring harness: Connect the electrical connector to the new starter’s solenoid, ensuring it clicks into place. Double-check the labels to ensure the wires are connected correctly.
Reconnect the battery: Reattach the negative terminal of the battery and tighten it securely.
Test the new starter: Start the vehicle to test if the new starter works properly. Listen for any abnormal sounds (e.g., grinding, clicking) and check if the engine starts smoothly. If there are any issues, turn off the engine immediately and troubleshoot.
Familiarize yourself with Chery iCAR’s engine layout: Different Chery iCAR models may have slightly different starter positions and mounting methods. Refer to the vehicle’s service manual for model-specific information.
Check for underlying issues: A faulty starter may be a symptom of a larger problem (e.g., a weak battery, a damaged flywheel ring gear, or a short circuit in the wiring). After replacing the starter, test these components to ensure the issue does not reoccur.
Use torque wrenches for bolt installation: Over-tightening or under-tightening the mounting bolts can cause damage to the starter or engine. Use a torque wrench to tighten the bolts to the specifications in the service manual.
Document the replacement: Keep a record of the starter replacement (part number, date, vehicle VIN) for future reference and to provide a warranty for the customer.
Solenoid Failure: The solenoid fails to generate enough electromagnetic force to engage the drive gear or close the main circuit. This is often caused by coil burnout, worn contacts, or a weak battery.
Worn Armature or Field Windings: The armature or field windings wear out due to prolonged use, leading to high resistance in the windings. This causes the starter to rotate slowly or not at all.
Drive Gear or One-Way Clutch Damage: The drive gear’s teeth wear out or the one-way clutch fails, leading to grinding sounds during startup or the drive gear failing to disengage after the engine starts.
Electrical Connection Issues: Loose or corroded wiring connections between the starter, battery, and solenoid cause poor contact, leading to intermittent starting issues or no starting at all.
Check the battery: A weak or depleted battery is a common cause of starting issues. Use a multimeter to test the battery’s voltage— a fully charged 48V battery should read around 52V, and a 72V battery should read around 78V. If the voltage is low, charge the battery and retest.
Inspect the wiring connections: Check the battery terminals, starter wiring harness, and solenoid connections for corrosion, looseness, or damage. Clean corroded terminals with a wire brush and tighten loose connections.
Listen for sounds during startup: Different sounds indicate different faults: - Clicking sound but no cranking: This usually indicates a faulty solenoid or a weak battery. - Grinding sound during cranking: This indicates damage to the drive gear or flywheel ring gear. - Whirring sound but no cranking: This indicates a failed one-way clutch (the armature is rotating but not driving the flywheel). - No sound at all: This indicates a faulty solenoid, open circuit in the wiring, or a completely dead battery.
Test the starter’s electrical system: Use a multimeter to test the voltage at the starter’s solenoid during startup. If the voltage is normal but the starter does not crank, the starter is faulty. If the voltage is low, the issue is with the battery or wiring.
Remove and inspect the starter: If the above steps do not identify the issue, remove the starter and inspect its components for wear, damage, or burnout. Check the solenoid, armature, field windings, and drive gear for signs of failure.
Visual inspection: Check the starter’s housing for cracks, melting, or oil leaks. Inspect the wiring harness and connections for corrosion, wear, or damage.
Electrical inspection: Use a multimeter to test the battery’s voltage and the starter’s current draw during startup. A higher-than-normal current draw indicates a worn starter.
Cleaning: Clean the battery terminals and starter connections with a wire brush and electrical contact cleaner to prevent corrosion.
Ensure the engine’s cooling system is working properly: A malfunctioning cooling system can cause the engine compartment to overheat, damaging the starter’s windings and solenoid.
Avoid driving in deep water: Water entering the starter can cause short circuits and corrosion. If the vehicle is driven in deep water, inspect the starter for water ingress and dry it thoroughly if necessary.
Check for oil leaks: Oil leaks from the engine can contaminate the starter, causing damage to the windings and bearings. If an oil leak is detected, repair it promptly.
Avoid frequent repeated starting: If the engine does not start on the first try, wait 10-15 seconds before trying again. This allows the starter to cool down and prevents overheating.
Do not start the engine when it is already running: This causes the drive gear to grind against the rotating flywheel ring gear, leading to wear.
Ensure the battery is fully charged: A weak battery causes the starter to work harder, drawing more current and accelerating wear.