Coil-on-Plug (COP) Type: Mounted directly on top of each spark plug, eliminating high-voltage ignition wires and reducing energy loss.
Pen-Type/Block-Type Coil: Connected to spark plugs via high-voltage wires, suitable for engines with shared ignition coils for multiple cylinders.
High-Efficiency Voltage Conversion & Stable Performance
Advanced Winding Technology: Adopts dual-winding structure with high-purity copper wire (oxygen-free copper) winding. The primary winding has low resistance and high current-carrying capacity, while the secondary winding has a high turns ratio, ensuring efficient conversion of low voltage to high voltage with minimal energy loss.
Precision Ignition Control: The iron core is made of high-permeability silicon steel sheet, which enhances magnetic field strength and improves voltage response speed. It can generate stable high voltage even under high engine speed conditions, avoiding misfires caused by insufficient spark energy.
Strong Anti-Interference Ability: The outer shell is equipped with a metal shielding layer to resist electromagnetic interference from the engine’s electrical system, preventing voltage fluctuations and ensuring consistent spark quality.
Durable Construction & Reliable Heat Dissipation
High-Temperature Resistant Material: The housing is made of reinforced PBT engineering plastic with glass fiber, which can withstand continuous high temperatures up to 180°C in the engine bay without deformation or cracking. The epoxy resin encapsulation inside the coil has excellent insulation and heat conduction performance, avoiding short circuits caused by high temperature or humidity.
Optimized Heat Dissipation Design: Coil-on-plug models feature a heat sink structure on the base, which increases the contact area with the cylinder head and accelerates heat dissipation. This reduces the coil’s operating temperature and extends its service life.
IP65 Waterproof & Dustproof Rating: The connector and wiring harness interface adopt a sealed rubber ring design, preventing water, oil, and dust from entering the coil interior, and ensuring stable operation in harsh environments such as rain and snow.
OE-Spec Compatibility & Plug-and-Play Installation
1:1 Original Design: Manufactured according to the original vehicle’s ignition coil dimensions, mounting hole positions, and connector pin definitions. It perfectly fits the engine cylinder head mounting bracket, requiring no drilling or modification.
Direct Replacement: No ECU programming or calibration is needed. For coil-on-plug types, simply disconnect the wiring harness connector, remove the fixing bolt, take out the old coil, and install the new one. For wire-connected types, replace the coil and check the high-voltage wire condition. The entire installation can be completed in 15–20 minutes by professional technicians.
Error-Free Operation: Matches the original ECU ignition parameters, avoiding fault codes (such as P0350-P0354) that may cause rough engine idle, reduced power, or increased fuel consumption.
Rigorous Testing & Long Service Life
Comprehensive Factory Testing: Each ignition coil undergoes high-voltage output testing, temperature cycle testing, and vibration fatigue testing to ensure performance meets OE standards. Only qualified products are delivered from the factory.
Extended Service Life: Under normal use conditions, the service life can reach 100,000–150,000 kilometers, which is 30% longer than that of ordinary aftermarket coils.
Environmentally Friendly Design: Lead-free and mercury-free materials are used in production, complying with international environmental standards such as RoHS.
Turn off the engine and disconnect the negative battery terminal to prevent electrical short circuits.
Wait for the engine to cool completely to avoid burns, as the ignition coil is close to the hot cylinder head.
Prepare tools including a socket wrench, torque wrench, and a clean cloth to wipe the spark plug hole and coil mounting surface.
Coil-on-Plug Type: Locate the ignition coil on top of the spark plug; disconnect the wiring harness connector by pressing the locking tab. Remove the fixing bolt with a socket wrench, then pull the coil straight up to take it out. Wipe the spark plug hole to remove dust and debris. Install the new coil, tighten the fixing bolt to the specified torque (usually 8–10 N·m), and reconnect the wiring harness.
Wire-Connected Type: Disconnect the high-voltage wires from the coil terminals; remove the coil fixing bolts and take out the old coil. Install the new coil, reconnect the high-voltage wires in the correct order, and tighten the fixing bolts.
Do not touch the high-voltage terminal of the ignition coil with bare hands when the engine is running, to avoid electric shock.
Check the ignition coil regularly for signs of damage such as cracks, oil leakage, or loose connectors. Replace it immediately if any fault is found.
Replace the spark plugs at the same time when replacing the ignition coil (if the spark plugs are worn), as worn spark plugs will increase the load on the coil and shorten its service life.
©2025 Hefei New Exeed Machinery Technology Co., Ltd. All rights reserved

